Win7 Bluescreens immer und immer wieder HP Compaq 500b

Moderator: jknoth

Post Reply
AdmiralRaccoon
Posts: 19
Joined: 13. May 2009, 09:44
Contact:

Win7 Bluescreens immer und immer wieder HP Compaq 500b

Post by AdmiralRaccoon » 03. Feb 2010, 09:22

Moin,

Ich verzweifel langsam an den Kisten hier...Nach der Postinstallation von Empirum gibts den ersten Bluescreen (BAD_POOL_HEADER, Stop 0x0000019). danach sofort wenn Windows in den Anmeldebildschirm kommt (jedes mal)
Booten kann ich nur im Safemode, dort hab ich auch schonmal alle Treiber nachinstalliert / erneuert (Gibts auch schon bei Win7), aber kein Erfolg.

Setze ich den PC per Hand mit dem gleichen Win7 auf, funktionierts.
Setze ich ez.b. ein FuSi E8110 auf, gehts auch mit Empirum.

Hat jemand eine Idee wo ich noch ansetzen könnte?

Soulman996
Posts: 20
Joined: 24. May 2006, 16:48
Location: Bochum
Contact:

Post by Soulman996 » 03. Feb 2010, 09:51

Immer wenn mir hier so BSOD unter kommen hat es immer was mit AHCI und seine Freunde zu tun.

Muß dann entweder die Platte im BIOS auf Compatibility umstellen oder den AHCI 10 bei der initialen installation mitkopieren lassen ($OEM$)

Vielleicht hilft es ja ...

AdmiralRaccoon
Posts: 19
Joined: 13. May 2009, 09:44
Contact:

Post by AdmiralRaccoon » 03. Feb 2010, 11:07

Ich versuchs mal mit den Treibern grade...
Das BIOS ist recht simpel gehalten, da gibts nix mehr mit Compatibility oder ähnliches. Nur SATA an und aus... :roll:

AdmiralRaccoon
Posts: 19
Joined: 13. May 2009, 09:44
Contact:

Post by AdmiralRaccoon » 03. Feb 2010, 12:46

Hat leider auch nix gebracht. :-(

Ich schieb´s aber mal Empirum und nicht der Hardware in die Schuhe, weil eine manuelle Installation (OS + MUI + Domain Joined) ohne Probleme funktioniert.

Ich weiss ja nicht was er nicht mag, aber ich muss die Dinger dann wohl per hand aufsetzen?

Soulman996
Posts: 20
Joined: 24. May 2006, 16:48
Location: Bochum
Contact:

Post by Soulman996 » 03. Feb 2010, 13:19

grade bei hp ist das sehr versteckt... das steht bei mir unter Speicheroption -> SATA Emulation dort kann man dann von AHCI IDE ode RAID auswählen

Vielleicht ist es ja auch wa sganz anderes das könnte man aber schnell kontrollieren....

User avatar
pkleiber
Posts: 831
Joined: 08. Dec 2004, 13:48
Contact:

Post by pkleiber » 03. Feb 2010, 15:11

Bitte den Inhalt des EPE Log posten.

Haben Sie für dieses Gerät einen SATA/SCSI Treiber integriert?
Patrick Kleiber
Support Engineer
Matrix42 AG

Disclaimer: I participate in this forum on a voluntary basis. Views expressed are not necessarily those of matrix42 AG.

AdmiralRaccoon
Posts: 19
Joined: 13. May 2009, 09:44
Contact:

Post by AdmiralRaccoon » 04. Feb 2010, 09:19

pkleiber wrote:Bitte den Inhalt des EPE Log posten.

Haben Sie für dieses Gerät einen SATA/SCSI Treiber integriert?
Hier das Log. Sonst hab ich nichts integriert, bis auf die GraKa hat Windows 7 scheinbar die passenden Treiber an Board.

Code: Select all

Begin time for EPE logging: Thu Feb  4 07:13:40 GMT 2010


Outputs of 'dmesg'
------------------------- DMESG --------------------

reg 14 64bit mmio pref: [0xd0000000-0xdfffffff]
pci 0000:01:00.0: reg 1c 64bit mmio pref: [0xce000000-0xcfffffff]
pci 0000:01:00.0: reg 24 io port: [0xdc00-0xdc7f]
pci 0000:01:00.0: reg 30 32bit mmio pref: [0xfea80000-0xfeafffff]
pci 0000:01:00.1: reg 10 32bit mmio: [0xfea7c000-0xfea7ffff]
pci 0000:00:01.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:01.0: bridge 32bit mmio: [0xfd000000-0xfeafffff]
pci 0000:00:01.0: bridge 64bit mmio pref: [0xce000000-0xdfffffff]
pci 0000:03:00.0: reg 10 io port: [0xe800-0xe8ff]
pci 0000:03:00.0: reg 18 64bit mmio: [0xfebff000-0xfebfffff]
pci 0000:03:00.0: reg 20 64bit mmio pref: [0xfbff0000-0xfbffffff]
pci 0000:03:00.0: reg 30 32bit mmio pref: [0x000000-0x01ffff]
pci 0000:03:00.0: supports D1 D2
pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge io port: [0xe000-0xefff]
pci 0000:00:1c.1: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
pci 0000:00:1c.1: bridge 64bit mmio pref: [0xfbf00000-0xfbffffff]
pci 0000:00:1e.0: transparent bridge
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs *3 4 5 6 7 10 11 12 14 15)
vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
PCI: Using ACPI for IRQ routing
Switching to clocksource tsc
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
system 00:06: ioport range 0xa00-0xa0f has been reserved
system 00:06: ioport range 0xa10-0xa1f has been reserved
system 00:06: ioport range 0xa20-0xa2f has been reserved
system 00:06: ioport range 0xa30-0xa3f has been reserved
system 00:07: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: ioport range 0x800-0x87f has been reserved
system 00:07: ioport range 0x480-0x4bf has been reserved
system 00:07: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:07: iomem range 0xfed20000-0xfed8ffff has been reserved
system 00:0a: iomem range 0xffc00000-0xffefffff has been reserved
system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0xbfffffff could not be reserved
pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
pci 0000:00:01.0:   IO window: 0xd000-0xdfff
pci 0000:00:01.0:   MEM window: 0xfd000000-0xfeafffff
pci 0000:00:01.0:   PREFETCH window: 0x000000ce000000-0x000000dfffffff
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:   IO window: 0x1000-0x1fff
pci 0000:00:1c.0:   MEM window: 0xc0000000-0xc01fffff
pci 0000:00:1c.0:   PREFETCH window: 0x000000c0200000-0x000000c03fffff
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:   IO window: 0xe000-0xefff
pci 0000:00:1c.1:   MEM window: 0xfeb00000-0xfebfffff
pci 0000:00:1c.1:   PREFETCH window: 0x000000fbf00000-0x000000fbffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:04
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: disabled
pci 0000:00:1e.0:   PREFETCH window: disabled
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
pci 0000:00:01.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
pci 0000:00:01.0: setting latency timer to 64
pci 0000:00:1c.0: enabling device (0104 -> 0107)
pci 0000:00:1c.0: PCI INT A -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
pci 0000:00:1c.0: setting latency timer to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
pci 0000:00:1c.1: PCI INT B -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
pci 0000:00:1c.1: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io:  [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfd000000-0xfeafffff]
pci_bus 0000:01: resource 2 pref mem [0xce000000-0xdfffffff]
pci_bus 0000:02: resource 0 io:  [0x1000-0x1fff]
pci_bus 0000:02: resource 1 mem: [0xc0000000-0xc01fffff]
pci_bus 0000:02: resource 2 pref mem [0xc0200000-0xc03fffff]
pci_bus 0000:03: resource 0 io:  [0xe000-0xefff]
pci_bus 0000:03: resource 1 mem: [0xfeb00000-0xfebfffff]
pci_bus 0000:03: resource 2 pref mem [0xfbf00000-0xfbffffff]
pci_bus 0000:04: resource 3 io:  [0x00-0xffff]
pci_bus 0000:04: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
pci 0000:01:00.0: Boot video device
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 18455k freed
Scanning for low memory corruption every 60 seconds
highmem bounce pool size: 64 pages
squashfs: version 4.0 (2009/01/31) Phillip Lougher
fuse init (API version 7.13)
msgmni has been set to 1717
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
pcieport 0000:00:01.0: setting latency timer to 64
pcieport 0000:00:1c.0: setting latency timer to 64
pcieport 0000:00:1c.1: setting latency timer to 64
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
vesafb: framebuffer at 0xcf000000, mapped to 0xf8100000, using 3072k, total 14336k
vesafb: mode is 1024x768x16, linelength=2048, pages=1
vesafb: protected mode interface info at c000:bf10
vesafb: pmi: set display start = c00cbf73, set palette = c00cbfce
vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da 
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing unused kernel memory: 256k freed
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ehci_hcd 0000:00:1d.7: PCI INT A -> Link[LNKH] -> GSI 3 (level, low) -> IRQ 3
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: using broken periodic workaround
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
ehci_hcd 0000:00:1d.7: irq 3, io mem 0xfcffbc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> Link[LNKH] -> GSI 3 (level, low) -> IRQ 3
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 3, io base 0x0000cc00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
uhci_hcd 0000:00:1d.1: PCI INT B -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 5, io base 0x0000c880
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
uhci_hcd 0000:00:1d.2: PCI INT C -> Link[LNKC] -> GSI 7 (level, low) -> IRQ 7
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 7, io base 0x0000c800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.3: PCI INT D -> Link[LNKA] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:1d.3: setting latency timer to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 10, io base 0x0000c480
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
sl811: driver sl811-hcd, 19 May 2005
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usbcore: registered new interface driver libusual
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 1-5: new high speed USB device using ehci_hcd and address 4
usb 1-5: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usb 1-7: new high speed USB device using ehci_hcd and address 5
usb 1-7: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /class/input/input0
generic-usb 0003:045E:0040.0001: input: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.0-1/input0
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
input: CHICONY HP Basic USB Keyboard as /class/input/input1
generic-usb 0003:03F0:0024.0002: input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1d.0-2/input0
usbcore: deregistering interface driver usb-storage
usbcore: deregistering interface driver libusual
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
input: PC Speaker as /class/input/input2
piix 0000:00:1f.1: IDE controller (0x8086:0x27df rev 0x01)
PIIX_IDE 0000:00:1f.1: PCI INT A -> Link[LNKC] -> GSI 7 (level, low) -> IRQ 7
piix 0000:00:1f.1: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7
    ide1: BM-DMA at 0xffa8-0xffaf
Probing IDE interface ide0...
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
r8169 0000:03:00.0: PCI INT A -> Link[LNKB] -> GSI 11 (level, low) -> IRQ 11
r8169 0000:03:00.0: setting latency timer to 64
r8169 0000:03:00.0: no MSI. Back to INTx.
eth0: RTL8102e at 0xf854c000, 18:a9:05:17:35:01, XID 04c00000 IRQ 11
SCSI subsystem initialized
libata version 3.00 loaded.
ata_piix 0000:00:1f.2: version 2.13
ata_piix 0000:00:1f.2: PCI INT B -> Link[LNKD] -> GSI 5 (level, low) -> IRQ 5
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: SATA max UDMA/133 cmd 0xc400 ctl 0xc080 bmdma 0xb880 irq 5
ata2: SATA max UDMA/133 cmd 0xc000 ctl 0xbc00 bmdma 0xb888 irq 5
ata1.00: ATA-8: SAMSUNG HD502IJ, 1AA01118, max UDMA/100
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.01: ATAPI: hp        DDVDW TS-H653R, 0E00, max UDMA/100
ata1.00: configured for UDMA/100
ata1.01: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      SAMSUNG HD502IJ  1AA0 PQ: 0 ANSI: 5
scsi 0:0:1:0: CD-ROM            hp       CDDVDW TS-H653R  0E00 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2
sd 0:0:0:0: [sda] Attached SCSI disk
ide-gd driver 1.18
NTFS driver 2.1.29 [Flags: R/O MODULE].
Slow work thread pool: Starting up
Slow work thread pool: Ready
SGI XFS with security attributes, large block/inode numbers, no debug enabled
JFS: nTxBlock = 8192, nTxLock = 65536
NET: Registered protocol family 33
kAFS: Red Hat AFS client v0.1 registering.
md: linear personality registered for level -1
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
md: raid10 personality registered for level 10
raid6: int32x1   1159 MB/s
raid6: int32x2   1068 MB/s
raid6: int32x4    813 MB/s
raid6: int32x8    828 MB/s
raid6: mmxx1     3847 MB/s
raid6: mmxx2     4341 MB/s
raid6: sse1x1    2636 MB/s
raid6: sse1x2    3297 MB/s
raid6: sse2x1    4610 MB/s
raid6: sse2x2    4910 MB/s
raid6: using algorithm sse2x2 (4910 MB/s)
device-mapper: multipath: version 1.1.0 loaded
md: raid1 personality registered for level 1
md: raid0 personality registered for level 0
md: multipath personality registered for level -4
async_tx: api initialized (async)
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  : 11212.000 MB/sec
xor: using function: pIII_sse (11212.000 MB/sec)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
device-mapper: multipath round-robin: version 1.0.0 loaded
---------------------- END DMESG ---------------------

Outputs of 'lsmod'
------------------------- LSMOD --------------------

Module                  Size  Used by
dm_mirror              10391  0 
dm_bbr                  8465  0 
dm_zero                  807  0 
dm_round_robin          1718  0 
raid456                42646  0 
async_raid6_recov       3935  1 raid456
async_pq                2568  2 raid456,async_raid6_recov
async_xor               1896  3 raid456,async_raid6_recov,async_pq
xor                    13205  1 async_xor
async_memcpy             887  2 raid456,async_raid6_recov
async_tx                1359  5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy
multipath               5146  0 
dm_crypt                9457  0 
dm_region_hash          5840  1 dm_mirror
dm_log                  6799  2 dm_mirror,dm_region_hash
raid0                   6072  0 
raid1                  16439  0 
dm_multipath           12415  1 dm_round_robin
raid6_pq               77492  2 async_raid6_recov,async_pq
raid10                 17294  0 
dm_snapshot            19108  0 
dm_mod                 48009  7 dm_mirror,dm_bbr,dm_zero,dm_crypt,dm_log,dm_multipath,dm_snapshot
linear                  3391  0 
md_mod                 69600  6 raid456,multipath,raid0,raid1,raid10,linear
kafs                   74519  0 
af_rxrpc               66657  3 kafs
msdos                   5042  0 
jfs                   136656  0 
udf                    65653  0 
crc_itu_t               1017  1 udf
xfs                   375085  0 
cifs                  177728  0 
coda                   21088  0 
ntfs                   76916  0 
exportfs                2787  1 xfs
reiserfs              173325  0 
minix                  21070  0 
ncpfs                  39036  0 
smbfs                  47595  0 
isofs                  25309  0 
ide_gd_mod             12933  0 
sd_mod                 20295  0 
ata_piix               17948  0 
libata                122076  1 ata_piix
scsi_mod              102947  2 sd_mod,libata
r8169                  30328  0 
mii                     2907  1 r8169
piix                    3865  0 
pcspkr                  1291  0 
sermouse                2631  0 
input_polldev           1491  0 
ff_memless              3207  0 
newtonkbd               1454  0 
sunkbd                  2993  0 
xtkbd                   1618  0 
edd                     6062  0 
usbhid                 28461  0 
sl811_hcd               8113  0 
uhci_hcd               17526  0 
ohci_hcd               18035  0 
isp116x_hcd            11469  0 
ehci_hcd               28615  0 
usbcore                98894  7 usbhid,sl811_hcd,uhci_hcd,ohci_hcd,isp116x_hcd,ehci_hcd
---------------------- END LSMOD ---------------------

Outputs of 'lspci'
------------------------- lspci --------------------

00:00.0 Host bridge: Intel Corporation: Unknown device 2e30 (rev 03)
00:01.0 PCI bridge: Intel Corporation: Unknown device 2e31 (rev 03)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation: Unknown device 0a60 (rev a2)
01:00.1 Audio device: nVidia Corporation: Unknown device 0be3 (rev a1)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E PCI Express Fast Ethernet controller (rev 02)
---------------------- END lspci ---------------------

Outputs of 'lspci -n'
------------------------- lspci -n --------------------

00:00.0 Class 0600: 8086:2e30 (rev 03)
00:01.0 Class 0604: 8086:2e31 (rev 03)
00:1b.0 Class 0403: 8086:27d8 (rev 01)
00:1c.0 Class 0604: 8086:27d0 (rev 01)
00:1c.1 Class 0604: 8086:27d2 (rev 01)
00:1d.0 Class 0c03: 8086:27c8 (rev 01)
00:1d.1 Class 0c03: 8086:27c9 (rev 01)
00:1d.2 Class 0c03: 8086:27ca (rev 01)
00:1d.3 Class 0c03: 8086:27cb (rev 01)
00:1d.7 Class 0c03: 8086:27cc (rev 01)
00:1e.0 Class 0604: 8086:244e (rev e1)
00:1f.0 Class 0601: 8086:27b8 (rev 01)
00:1f.1 Class 0101: 8086:27df (rev 01)
00:1f.2 Class 0101: 8086:27c0 (rev 01)
00:1f.3 Class 0c05: 8086:27da (rev 01)
01:00.0 Class 0300: 10de:0a60 (rev a2)
01:00.1 Class 0403: 10de:0be3 (rev a1)
03:00.0 Class 0200: 10ec:8136 (rev 02)
---------------------- END lspci -n ---------------------

Content of '/proc/partitions'
------------------------- /proc/partitions --------------------

major minor  #blocks  name

   8        0  488386584 sda
   8        1     102400 sda1
   8        2  488282112 sda2
---------------------- END /proc/partitions ---------------------

Content of '/proc/net/dev'
------------------------- /proc/net/dev --------------------

Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo frame compressed multicast|bytes    packets errs drop fifo colls carrier compressed
    lo: 5615151    3836    0    0    0     0          0         0  5615151    3836    0    0    0     0       0          0
  sit0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
  eth0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0
---------------------- END /proc/net/dev ---------------------

Content of '/proc/cmdline'
------------------------- /proc/cmdline --------------------

BOOT_IMAGE=/epe-win7/kernel ramdisk_size=328192 init=/bin/minit CONSOLE=/dev/tty1 vga=0x317 root=/dev/ram0 rw quiet irqpoll pci=nomsi EPE_LANGUAGE=ENU EPE_OSSEL=0 initrd=./epe-win7/initrd.gz
---------------------- END /proc/cmdline ---------------------

ls -l /lib/modules/
------------------------- /lib/modules/ --------------------

total 1
drwxr-xr-x 3 root root 1024 Feb  4 07:12 2.6.32-gentoo
---------------------- END /lib/modules/ ---------------------

uname -r
------------------------- uname -r --------------------

2.6.32-gentoo
---------------------- END uname -r ---------------------

Content of '/tmp/pcitable'
------------------------- /tmp/pcitable --------------------

"0x00008086"  "0x000027df" "0xffffffff" "0xffffffff" "piix" "Empirum detected Mass Storage Controller"
"0x00008086"  "0x000027c0" "0xffffffff" "0xffffffff" "ata_piix" "Empirum detected Mass Storage Controller"
"0x000010ec"  "0x00008136" "0xffffffff" "0xffffffff" "r8169" "Empirum detected Network Interface Card"
---------------------- END /tmp/pcitable ---------------------

------------------------- Debug Messages --------------------
10 uncrypt reading disk.ini
0 uncrypt decrypting ...
0 uncrypt decryption completed successfully
5 syslog catching pending Kernel-messages
10 boot msg_enter
0 boot mounting /proc
0 boot mounting /sys
5 boot performing udev initial scan
5 boot making udev managing hotplug events
0 boot choosing network mode
0 boot  network mode:  dhcp
10 syslog starting klogd
10 syslog starting syslogd
0 boot setting up modul-dependentcies
0 boot setting hostname
0 boot checking if CPU has 64Bit capability
0 boot CPU has 64Bit capability
0 boot preparing modules
0 boot updating modules.conf
0 boot loading usb modules
10 lo entering runlevel
1 lo setting up loopback interface
1 lo Loopback interface succsessfully set up
10 httpd entering runlevel
10 startx entering runlevel
0 startx starting Tiny-X for framebuffer devices Xfbdev
1 httpd Configuring .htaccess
1 httpd htpassword successfully configured
1 httpd setting environment-variable $DESKTOP_DEST
1 httpd httpd starting httpd
0 startx setting DISPLAY-variable
0 startx Starting Browser
10 startx browser executed successfully
10 modsetup entering runlevel
0 modsetup preparing modules directory
0 modsetup removing usb_storage
0 modsetup loading edd support
0 modsetup loading input device driver
0 modsetup installing Driver xtkbd
0 modsetup installing Driver sunkbd
0 modsetup installing Driver newtonkbd
0 modsetup installing Driver ff-memless
0 modsetup installing Driver input-polldev
0 modsetup installing Driver sermouse
0 modsetup installing Driver pcspkr
0 modsetup installing Installing IDE-drivers
0 modsetup installing NIC-drivers
0 modsetup installing SCSI-drivers
0 modsetup loading scsi low-level-drivers
0 modsetup loading inserting scsi disk-driver
0 modsetup loading inserting ide disk-driver
0 modsetup loading fs-support
0 modsetup installing Driver smbfs
0 modsetup installing Driver ncpfs
0 modsetup installing Driver minix
0 modsetup installing Driver isofs
0 modsetup installing Driver reiserfs
0 modsetup installing Driver exportfs
0 modsetup installing Driver ntfs
0 modsetup installing Driver coda
0 modsetup installing Driver cifs
0 modsetup installing Driver xfs
0 modsetup installing Driver udf
0 modsetup installing Driver jfs
0 modsetup installing Driver msdos
0 modsetup installing Driver kafs
0 modsetup loading raid and lvm
0 modsetup installing Driver md-mod
0 modsetup installing Driver linear
0 modsetup installing Driver dm-snapshot
0 modsetup installing Driver raid10
0 modsetup installing Driver raid6_pq
0 modsetup installing Driver dm-multipath
0 modsetup installing Driver raid1
0 modsetup installing Driver raid0
0 modsetup installing Driver dm-region-hash
0 modsetup installing Driver dm-crypt
0 modsetup installing Driver multipath
0 modsetup installing Driver raid456
0 modsetup installing Driver dm-round-robin
0 modsetup installing Driver dm-mod
0 modsetup installing Driver dm-log
0 modsetup installing Driver dm-zero
0 modsetup installing Driver dm-bbr
0 modsetup installing Driver dm-mirror
0 modsetup Storage Adapter: 0x00008086-0x000027df-0xffffffff-0xffffffff 
0 modsetup Storage Adapter: 0x00008086-0x000027c0-0xffffffff-0xffffffff 
0 modsetup Network Adapter: 0x000010ec-0x00008136-0xffffffff-0xffffffff 
------------------------- End Debug Messages -------------------- 

Post Reply

Return to “OS Installer”

Who is online

Users browsing this forum: No registered users and 2 guests